One-for-all URC-7010 Manual de usuario Pagina 11
- Pagina / 18
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
WWW.ONEFORALL.COM 11
Trouble-Shooting
Problem:
Your brand is not listed in the
code section?
The ONE FOR ALL does not
operate your device(s)?
The ONE FOR ALL is not
performing commands
properly?
Problems changing channels?
The ONE FOR ALL does not
respond after pressing a key?
The red light does not blink
when you press a key?
Solution:
Try the search method on page 7.
A) Try all the codes listed for your
brand.
B) Try the search method on page 7.
You may be using the wrong code. Try
repeating the Direct Set-Up using
another code listed under your brand
or start the search method over again
to locate the proper code.
Enter the programme number exactly
as you would on your original remote.
Make sure you are using new batteries
and are aiming the ONE FOR ALL at
your television.
Replace batteries with 2 fresh, new
“AA/LR6” alkaline batteries.
ONE FOR ALL Recall (Previous Channel)
If your television has a Recall or Previous / Last Channel function, the Recall
key allows you to access this function. If, however, your television does not
have a Recall or Previous / Last Channel function, then you can set up your
own two favourite channels with the ONE FOR ALL Recall function.
The ONE FOR ALL Recall function allows you to program up to two channels,
each consisting of a maximum of 4 key presses per channel entry. This allows you
to swap back and forth between two channels with the press of a single key.
1 Press the MAGIC and RECALL keys simultaneously, until the red
light blinks twice.
2 Enter the first channel number exactly as you would on your
original remote (e.g. <-/-->, <1>, <2> to get channel number 12).
3 Press RECALL once and release.
4 Enter the second channel number exactly as you would on your
original remote (e.g. <-/-->, <2>, <3> to get channel number 23).
5 Press the MAGIC key, and the red light blinks twice.
Now, if you press RECALL, you will obtain the second channel programmed
(being <23>) and if you press RECALL again you will obtain the first chan-
nel programmed (being <12> in our example).
To reset the RECALL key:
1 Press MAGIC and RECALL simultaneously until the red light
blinks twice.
2 Press RECALL and release.
3 Press MAGIC and release and the red light will blink twice.
Important notes:
- To enter only one channel number, skip steps 3 & 4.
- If two channel numbers have been stored previously, entering one new
channel will delete the oldest entry.
- ONE FOR ALL 1 1
- 2 WWW.ONEFORALL.COM 2
- About Your ONE FOR ALL 1 2
- Table of Contents 2
- WWW.ONEFORALL.COM 3 3
- WWW.ONEFORALL.COM 4 4
- WWW.ONEFORALL.COM 5 5
- 6 WWW.ONEFORALL.COM 6
- Setting Up Your Television 6
- Installation 6
- The Search Method 7
- ■■ ■■ ■■ ■■ 8
- Colour and Brightness 9
- Auto Scan 9
- Advanced Features 9
- 10 WWW.ONEFORALL.COM 10
- Device Sleeptimer 10
- ONE FOR ALL Sleeptimer 10
- Trouble-Shooting 11
- To reset the RECALL key: 11
- 12 WWW.ONEFORALL.COM 12
- Customer Service 12
- 0565 0087 13
- 74 WWW.ONEFORALL.COM 14
- 76 WWW.ONEFORALL.COM 16
- URC-7010 18
- Printed on Recycled Paper 18
Relacionado con productos y manuales para Control remoto One-for-all URC-7010
Control remoto One-for-all URC-7781 Manual de usuario
(319 paginas)
(319 paginas)
Control remoto One-for-all 704918 Manual de usuario
(168 paginas)
(168 paginas)
Control remoto One-for-all URC-7525 Manual de usuario
(107 paginas)
(107 paginas)
Control remoto One-for-all HC-8000 Manual de usuario
(114 paginas)
(114 paginas)
Control remoto One-for-all URC-7556 Manual de usuario
(224 paginas)
(224 paginas)
LG W2220P-BF Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Computerzubehör LG W2220P-BF.
Wir stellen 3 PDF-Handbücher LG W2220P-BF zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Comentarios a estos manuales